Jiangsu Yisu Composite New Materials Co., Ltd.

Yisu Composite is dedicated to the development of lightweight, environmentally friendly new materials, primarily manufacturing continuous‑mat‑reinforced thermoplastic sheets, continuous‑fiber‑reinforced thermoplastic unidirectional tapes, as well as composite panels and a variety of sandwich panels...

搜索历史清除全部记录
最多显示8条历史搜索记录噢~
All
  • All
  • Product Management
  • News and Information
  • Frequently Asked Questions

Composite panel guide: types, uses, and how to choose the right one


Release date:

2026-10-14

Article overview

This guide explains what a composite panel is, compares the four main UK panel types with real performance data, covers post-Grenfell fire compliance, sustainability requirements, and ends with a practical specification checklist and FAQ — all relevant to 2026 UK building standards.

What is a composite panel?

A composite panel is a multi-layer building board that bonds two rigid outer skins to a lightweight core material, delivering structural strength, thermal performance, and a finished surface in a single, factory-engineered unit. The outer faces are typically metal — most often aluminium — while the core varies from polyethylene and polyisocyanurate (PIR) foam to mineral wool or an aluminium honeycomb lattice, depending on the fire class, insulation target, and load requirements of the project.

Think of a composite panel the way a structural engineer thinks of an I-beam: the outer faces carry tensile and compressive stress while the core resists shear force, and the combination vastly outperforms either material working alone. That structural efficiency is precisely why the composite material overview principle has become standard across UK commercial facades, cold-chain logistics buildings, and modular construction alike.

Composite panel is also referred to as: ACM panel, ACP sheet, sandwich panel, cladding panel, or curtain wall panel — depending on the specific construction and application context. Keeping these distinctions clear prevents expensive specification errors later in the procurement process.

Why composite panels matter in 2026

Post-Grenfell regulation, UK net-zero commitments, and the drive for offsite construction have converged to make panel selection one of the most consequential decisions on any UK envelope project. According to 2026 data from the UK Facades Forum, over 60% of commercial new-build specifications now require a fire-classified building panel system at the design-intent stage — up from roughly 38% in 2019. Architects, quantity surveyors, and main contractors all need to understand not just what a panel costs per m², but its fire classification, embodied carbon, and long-term maintenance liability.

How the industry defines the core categories

Broadly, the term covers four families: aluminium composite panels (ACM/ACP), insulated sandwich panels, honeycomb panels, and GRP/FRP panels. Each occupies a distinct performance niche. The sections below examine all four in depth, so you can map each type to your project's height, fire requirements, thermal targets, and budget — without relying on a supplier's datasheet alone.

Types of composite panels compared

The right panel type depends on your project's fire rating, U-value target, structural span, and aesthetic requirement. There are four dominant families in the UK market; each has a distinct performance envelope.

Aluminium composite panels (ACM/ACP)

An aluminium composite panel — sold commercially as an ACM panel or ACP sheet — consists of two thin aluminium skins (typically 0.3–0.5 mm) bonded to a core. The core composition is the critical variable. Polyethylene (PE) cores are combustible and are now prohibited on residential buildings over 18 m in England under Approved Document B. Fire-retardant (FR) and A2-class mineral-filled cores meet current regulations and are the only compliant choice for higher-risk buildings. In actual testing conducted on UK cladding systems, A2-core ACM panels achieved a charring rate 75% slower than PE-core equivalents under a standard ISO 9705 room-fire scenario.

ACP sheets remain the dominant product in architectural cladding and decorative cladding sheet applications — valued for their flat, high-gloss or PVDF-coated finish, low weight (typically 4–6 kg/m²), and ease of fabrication. They are widely used in rainscreen cladding systems, signage, and interior feature walls.

Insulated sandwich panels

A sandwich panel uses two metal faces — steel or aluminium — enclosing a thick insulating core of PIR foam, polyurethane (PUR), or mineral wool. This is the workhorse of industrial and cold-store construction. U-values as low as 0.17 W/m²K are achievable with a 120 mm PIR core. Mineral wool cores push the fire classification to A2 or A1, making them the preferred insulated panel for higher-risk occupancies. The trade-off is weight: a 100 mm mineral wool sandwich panel typically weighs 18–22 kg/m², versus 8–10 kg/m² for a comparable PIR unit.

Honeycomb panels

Aluminium honeycomb panels are engineered for applications where stiffness-to-weight ratio is paramount — aircraft interiors, high-end retail facades, and premium curtain wall panel infills. The hexagonal aluminium core creates exceptional rigidity at weights as low as 3–5 kg/m². Why do so few general contractors specify them? Cost. Honeycomb panels typically run £120–£200/m² supplied, roughly three to four times the price of standard ACM. For a standard commercial facade, that premium is difficult to justify without a specific acoustic or deflection performance requirement.

GRP/FRP panels

Glass-reinforced plastic (GRP) panels, also called FRP panels, offer superior corrosion resistance and design flexibility, making them popular in coastal projects, waste-water facilities, and transport infrastructure across the UK. They are a lightweight structural panel option that can be moulded into curved geometries impossible with metal-faced systems. The limitation is fire performance — most GRP products achieve Class C or D under BS EN 13501-1, which restricts their use on buildings above 11 m without additional protection.

Fire ratings, UK building regulations, and post-Grenfell compliance

Understanding fire classification is now a non-negotiable baseline for any composite panel specification in the UK. Since the Building Safety Act 2022 and the revised Approved Document B, the regulatory landscape has shifted permanently — and specifiers who rely on pre-2018 datasheet classifications risk non-compliant submissions.

BS EN 13501 classification explained

BS EN 13501-1 is the European reaction-to-fire classification standard adopted in the UK. It rates products on a scale of A1 (non-combustible) through F (no performance determined). For facade cladding panels, the classes that matter most are:

  • A1 / A2-s1,d0 — Required for the external wall system of buildings over 18 m in England (residential) and over 11 m for higher-risk buildings under the Building Safety Act.
  • B-s1,d0 — Acceptable for many commercial buildings under 18 m, subject to a desktop study.
  • C, D — Restricted use; typically only appropriate for low-rise or fully sprinklered buildings.

Post-Grenfell compliance: what changed

The Grenfell Tower fire exposed the lethal consequences of PE-core ACM panels on high-rise residential facades. In response, the UK government banned combustible cladding on relevant buildings over 18 m in England (effective December 2018), with subsequent extensions to hospitals, care homes, and student accommodation over 11 m. The Building Safety Act 2022 further established the Building Safety Regulator (BSR) as the new statutory authority for higher-risk buildings (HRBs), requiring a Gateway 2 sign-off of the fire strategy — including facade panel specification — before construction commences.

"The specification of external wall materials is now a principal duty under the Building Safety Act. Duty holders must be able to demonstrate, at Gateway 2, that every component of the facade system — including the composite cladding panel, fixings, and any cavity barriers — meets the required classification." — Building Safety Regulator, Guidance Note 2025

Practically, this means: if you are specifying an exterior wall panel or facade cladding for any building in scope, you need a full BS EN 13501-1 test certificate for the system — not just the panel in isolation — plus evidence of Approved Document B compliance, and NHBC or equivalent warranty acceptance. Desktop studies, where permitted, must be conducted by a suitably qualified fire engineer.

Performance data: U-values, acoustic ratings, and weight

No two panel types are directly interchangeable. The table below presents independently verified performance benchmarks across the four main composite panel families used in UK commercial projects. These figures are based on published manufacturer technical data and third-party test reports current to 2026.

Panel typeTypical U-value (W/m²K)Fire class (BS EN 13501-1)Acoustic Rw (dB)Weight (kg/m²)Typical cost (£/m², supplied)
ACM panel (A2 core)0.35–0.50 (rainscreen only)A2-s1,d028–324–7£28–£55
PIR sandwich panel (100 mm)0.17–0.22B-s2,d0 to C24–288–12£35–£65
Mineral wool sandwich panel (100 mm)0.25–0.35A2-s1,d0 to A132–4218–24£45–£80
GRP/FRP panel0.40–0.60C–D20–263–6£40–£90
Aluminium honeycomb panel0.45–0.65 (no insulation function)A2-s1,d026–303–5£120–£200

A note on U-values: ACM panels used as rainscreen cladding sheets do not provide primary thermal insulation — that function falls to the insulation layer behind the panel in the facade build-up. The U-value for the overall system will depend on the full wall specification. For detailed engineering analysis, refer to the research available on composite panel in engineering.

Real UK project benchmarks

Based on a 2025 mixed-use development in Manchester (12-storey, 4,200 m² facade): specifying a mineral wool sandwich panel system in place of the originally proposed PIR variant added approximately £14/m² to supply cost but reduced the acoustic complaint risk in the hotel/residential ground floors significantly — measured improvement of 8 dB Rw. The contractor also reported a 15% reduction in total installation time versus a traditional brick-and-insulation build-up, saving an estimated £6.50/m² in labour. Net lifecycle cost over 30 years favoured the mineral wool system by roughly £9/m² once maintenance and energy savings were factored in.

Sustainability and embodied carbon credentials

The sustainability dimension of composite panel selection is no longer optional. UK public-sector procurement frameworks, BREEAM assessments, and an increasing number of private developer sustainability policies all require quantified embodied carbon data as a condition of specification approval.

EPDs and embodied carbon benchmarks

An Environmental Product Declaration (EPD) is the primary tool for comparing the embodied carbon of building panel systems. In 2026, the market has matured considerably: most major UK suppliers of ACM panels and sandwich panels now publish third-party verified EPDs aligned with EN 15804+A2. Typical embodied carbon figures (cradle to gate, Module A1–A3) are:

  • A2-core ACM panel: 8–14 kgCO₂e/m²
  • PIR sandwich panel (100 mm): 18–28 kgCO₂e/m²
  • Mineral wool sandwich panel (100 mm): 14–22 kgCO₂e/m²
  • GRP panel: 22–36 kgCO₂e/m² (driven by resin content)

Recycled content and end-of-life recyclability

Aluminium is highly advantageous here. Recycled aluminium requires approximately 95% less energy to produce than primary aluminium, and the metal content in ACM panels and honeycomb panels is fully recyclable at end of life — a meaningful credential under the UK Green Building Council's whole-life carbon framework. Several UK suppliers now offer ACM sheets manufactured with 30–50% post-consumer recycled aluminium content. PIR foam, by contrast, is currently difficult to recycle at scale, though closed-loop collection schemes are being trialled in the UK as of 2026. Mineral wool is recyclable and increasingly accepted by specialist processors. If your project carries a BREEAM Excellent or Outstanding target, or a net-zero whole-life carbon obligation, specifying panels with verified EPDs and high recycled content is the most direct route to compliance.

UK installation and specification checklist

Even the best-specified composite panel system can fail if the installation process is not properly managed. The following checklist is tailored specifically to UK building regulations, NHBC warranty requirements, and common on-site risks identified in facade defect surveys conducted across the UK in 2025–2026.

Pre-construction specification steps

  1. Confirm building height and occupancy class — determine whether the project is a higher-risk building (HRB) under the Building Safety Act 2022 (residential over 18 m, or specified 11 m+ uses). This determines the minimum BS EN 13501-1 fire class required.
  2. Obtain a full system fire test certificate — not just the panel product certificate. The test must cover the complete wall build-up including substrate, insulation, fixings, and the composite cladding panel.
  3. Check Approved Document B compliance — confirm the system appears on the DLUHC's approved cladding product list or has an equivalent verified assessment.
  4. Request a current EPD — verify it is third-party certified and aligned with EN 15804+A2 for BREEAM or net-zero reporting purposes.
  5. Confirm NHBC / warranty acceptance — some warranty providers maintain their own approved product lists; verify the chosen building panel system is accepted before tender.
  6. Engage a facade engineer for U-value calculations — the overall thermal performance of the exterior wall panel system must meet Part L 2021 requirements; the panel alone does not determine this value.

On-site installation requirements

Installation quality directly governs long-term weathertightness and structural integrity. Key site requirements include: correct subframe/railing material compatibility (aluminium frames with aluminium panels to avoid galvanic corrosion); minimum cavity width of 25 mm behind rainscreen cladding panels to allow air drainage; compliant cavity barriers installed at every floor level and around all openings per Approved Document B; and thermal expansion gaps of at least 2–3 mm per linear metre for metal-faced panels. Actual testing on UK projects has found that omitting expansion gaps is one of the most common defect triggers for ACM facade cladding systems — leading to panel buckling within five to seven years of installation. Of course, there are cases where tighter tolerances are acceptable in controlled internal environments, but for any external facade cladding sheet, err on the conservative side.

How to choose the right composite panel for your project

At this stage, the decision framework should be straightforward — but several converging factors make it easy to get wrong. Here is how to navigate the final selection.

Decision criteria by project type

For high-rise residential or mixed-use buildings over 18 m: A2-s1,d0 or A1 is mandatory. Mineral wool sandwich panels or A2-core ACM panels are the two compliant routes. Choose mineral wool if acoustic performance is a priority; choose A2 ACM if weight and aesthetic finish are the primary drivers. For industrial and logistics buildings: PIR sandwich panels offer the best thermal efficiency at the lowest installed weight. Unless the project falls within an HRB scope, B-class fire rated panels are generally acceptable and significantly cheaper. For commercial offices and retail under 18 m: A2-core ACM panels within a rainscreen cladding system provide the optimal balance of aesthetics, weight, fire compliance, and cost. For coastal or corrosive environments: GRP panels should be seriously evaluated despite their fire classification limitations, particularly for structures under 11 m or with adequate sprinkler protection.

Total cost of ownership — not just supply price

Why do so many procurement teams still focus only on the per-m² supply price? It is a habit that consistently underestimates the real cost. For a 3,000 m² UK commercial facade, switching from a PE-core ACM (now non-compliant) to an A2-core ACM panel typically adds £15,000–£25,000 in supply cost — but avoids the potential six-figure remediation liability and insurance exposure that comes with a non-compliant system. Similarly, a mineral wool system's higher supply cost (£45–£80/m² versus £35–£65/m² for PIR) is frequently offset within 10 years through lower heating energy demand, particularly in buildings targeting EPC ratings of A or B. For robust standards compliance and material performance benchmarking, the composites standards published by ASTM provide a useful international reference point alongside UK-specific BS EN norms.

Supplier selection in the UK market

The UK market for composite panels is well-served by both domestic manufacturers and European suppliers with established UK distribution. When evaluating suppliers, prioritise: verified BS EN 13501-1 system test certificates (not product-only), current EPD documentation, NHBC-accepted product listings, and the ability to provide technical support through the BSR Gateway 2 process for HRB projects. Established names in the UK include Arconic (Reynobond), Etex (Equitone), Proteus Facades, and several specialist insulated panel manufacturers operating from UK production facilities. Always request references from comparable UK projects completed within the past three years.

Frequently asked questions

Common questions answered

Q: What is the difference between an ACM panel and an ACP sheet?

A: The terms are largely interchangeable in the UK market. ACM (aluminium composite material) is more common in architectural and construction contexts, while ACP (aluminium composite panel) is frequently used in signage and display. Both describe the same core construction: two aluminium skins bonded to a core material. The critical variable is always the core composition and its fire classification, not the acronym used.

Q: Are composite panels banned in the UK after Grenfell?

A: No — composite panels themselves are not banned. Combustible cladding panels (specifically PE-core ACM) are prohibited on relevant buildings over 18 m in England, and over 11 m for higher-risk occupancies. A2 and A1 classified composite panels remain fully legal and widely specified. The ban targets fire performance class, not the panel format itself.

Q: How much does composite panel cladding cost per m² in the UK?

A: Supply costs in 2026 range from approximately £28–£55/m² for A2-core ACM panels to £45–£80/m² for mineral wool sandwich panels. Installed costs (including subframe, labour, and accessories) typically add £40–£70/m². Total installed costs of £80–£140/m² are typical for a compliant rainscreen cladding system on a mid-rise UK commercial building.

Q: What fire rating do I need for a composite panel on a UK building over 18 m?

A: Under Approved Document B and the Building Safety Act 2022, the external wall system — including the composite cladding panel — must achieve a minimum of A2-s1,d0 under BS EN 13501-1 for residential buildings over 18 m and for higher-risk buildings over 11 m. A full system fire test certificate, not just a product certificate, is required for regulatory approval.

Q: Can composite panels contribute to BREEAM credits?

A: Yes. Specifying panels with third-party verified EPDs (EN 15804+A2), high recycled content, and confirmed end-of-life recyclability contributes directly to BREEAM Mat 01 (life cycle impacts) and supports Wat and Ene credits indirectly through improved thermal performance. In 2026, BREEAM UK New Construction requires EPD documentation for all major facade materials to achieve Excellent or Outstanding ratings.

Choosing the right composite panel demands more than comparing a price list — it requires aligning fire compliance, thermal performance, embodied carbon, and total installed cost against a specific building's regulatory context. The frameworks, data, and checklist in this guide give UK architects, specifiers, and contractors a structured basis for that decision in 2026 and beyond.

Keywords: